Vector Compact Pro Vec020c User Manual

VEC0 2 0 C  
TM  
p r o  
JUM P - START SYSTEM , AIR CO M P RESSO R  
AND P O W ER SUP P LY  
Po rta b le , Co rd le ss, Re ch a rg e a b le 1 2 Vo lt DC  
O W N ER’S MAN UAL  
& WARRAN TY IN FO RMATIO N  
THIS MAN UAL CO N TAIN S IMPO RTAN T IN FO RMATIO N REGARDIN G SAFETY,  
O PERATIO N , MAIN TEN AN CE AN D STO RAGE O F THIS PRO DUCT. BEFO RE USIN G,  
READ AN D UN DERSTAN D ALL CAUTIO N S, WARN IN GS, IN STRUCTIO N S AN D  
PRO DUCT LABELS, PLUS YO UR VEHICLES BATTERY MANUFACTURER GUIDELINES.  
FAILURE TO DO SO CO ULD RESULT IN IN JURY AN D/ O R PRO PERTY DAMAGE.  
4 1 4 0 SW 2 8 TH W AY, FT. LAUDERDALE, FL 3 3 3 1 2  
TEL 9 5 4 -5 8 4 -4 4 4 6 TO LL FREE: 8 6 6 -5 8 4 -5 5 0 4 • FAX 9 5 4 -5 8 4 -5 5 5 6  
w w w .ve cto rm fg .co m  
CONTENTS  
1. IN TRO DUCTIO N ................................................................................. 4 ,5  
2. USIN G START-IT CO MPACT PRO ™ AS A JUMPSTART SYSTEM .............. 5 ,6  
2.1 Easy, Step-by-Step Jumpstarting Instructions ...................................................... 6,7  
3. CHARGIN G/ RECHARGIN G ................................................................. 7  
3.1 110/ 120-Volt AC Charging ............................................................................. 8  
3.2 12-Volt DC Charging ....................................................................................... 8  
3.3 Estimated Battery Life ....................................................................................... 8  
4. O PERATIN G AS A PO RTABLE PO W ER SUPPLY ..................................... 9  
5. EMERGEN CY/ W O RK LIGHT ................................................................ 9  
6. CO MPRESSO R/ TIRE IN FLATO R ........................................................... 9  
6.1 Compressor Use ............................................................................................... 10  
6.2 Warnings for Compressor Use .......................................................................... 10  
6.3 Tire Inflation or Products w/ Valve Stem ............................................................ 10  
6.4 Inflate other Articles (w/ out Valve Stem) ............................................................ 10  
6.5 Typical Inflation Times ...................................................................................... 10  
7. REPLACEMEN T PARTS ......................................................................... 1 1  
7.1 Battery Disposal ............................................................................................... 11  
7.2 Battery Replacement......................................................................................... 11  
7.3 Battery Disposal ............................................................................................... 11  
8. SPECIFICATIO N S ................................................................................ 1 1  
WARRAN TY ....................................................................................... 1 2  
3
1.  
INTRODUCTION  
Congratulations on selecting the Vector® START-IT COMPACT PROJUMPSTART SYSTEM,  
AIR COMPRESSOR and 12 VOLT DC POWER SUPPLY. This compact jumpstarter is unique in  
the amount of energy it can supply for its size. The internal battery is a Vector-developed high  
density sealed lead acid battery that stores and delivers energy comparable to full sized  
ordinary jumpstarters. Please read this guide carefully before use to ensure optimum  
performance and avoid damage to the unit or items that you are using it with.  
A standard feature of this model is a high pressure, self-contained tire compressor with lighted  
gauge. This compressor allows quick inflation of vehicle tires to 260 PSI and with supplied  
adapter nozzles, inflates beach balls, rafts and virtually any low-pressure inflatables. Three  
different sized nozzles allow for easy connection to all popular inflatables.  
The Vector® START-IT COMPACT PROJUMPSTART SYSTEM & 12 VOLT DC POWER SUPPLY  
is a compact, durable and portable jumpstart system for vehicles and boats that have a  
standard 12-Volt battery system. This self-contained, rechargeable system will start most  
vehicles and boats without the need for a host vehicle or 110/ 120 Volt AC power supply. It can  
also be used as a safe, portable source of 12-volt DC electric power in remote locations and/  
or emergency situations. It is ideal for use with Vector 12 Volt DC cordless, portable, recharge-  
able products and MAX DC/ AC Power Inverters. Use the START-IT COMPACT PROto:  
Jumpstart: Any engine system with a standard 12 Volt DC battery: boat, truck, car, airplane,  
RV, personal watercraft, snowmobile, garden tractor, gasoline engine generator, etc.  
Operate: 12-volt DC Fans, inflators, fluorescent work lights, cellular phones*, spotlights,  
TVs, portable radios, cassette or CD players, and more. *Can quick-charge a cellular  
phone by using the phones 12-volt DC adapter cord.-Operate: Certain 110/ 120 Volt AC  
Accessories (requires a Vector 12 volt power inverter, sold separately) .  
The START-IT COMPACT PRO SYSTEM has an easy-to-read, series of LED (Light Emitting Diode)  
charge indicators that show when the unit is fully charged, or the level of charge in the battery.  
Charge level can be viewed when the charge status push button is pressed. A 12 Volt DC  
cigarette lighter-type socket is provided for use with appliances that can operate from a vehicle  
ciga rette lighter. This a llows ma ximum porta bility a nd utility when the START-IT  
COMPACT PRO is used in remote locations.  
START-IT COMPACT PROcan be recharged from any standard 110/ 120 Volt AC power  
source using the supplied AC Recharge Adapter. The adapters barrel connector attaches to the  
Recharge Port on the top panel of the junpstarter. A built-in 12-volt appliance socket and the  
appropriate DC/ DC charging/ adapter cord is used to recharge the battery from another  
12 volt DC source. When pressed, the CHARGE STATUS button will show the battery ‘s power  
level status (from Low to Full). The green LED full indicator illuminates when the unit is fully  
recharged and charging can be discontinued. An ON/ OFF switch operates the built-in work/  
emergency light.  
1 2  
1 0  
1 1  
FIGURE 1  
2
3
7
4
1
5
9
6
8
4
1. 12 Volt DC Accessory Socket, with 20 amp overload protection  
2. Safety ON/ OFF Power Switch (No Key Required)  
3. Charge Status Push Button  
4. LED Charging/ Battery Status Indicators  
5. Heavy-Duty #6AWG Welding Quality Jumper Cables  
6. Heavy-Duty, 350 Amp Copper Clamps  
7. Exclusive, Quick-Release, Clamp Holsters  
8. 110/ 120-Volt UL approved AC/ DC Charging Adapter Cord  
9. 12 Volt DC/ DC Charging Adapter Cord  
10. Built-in Emergency Work light  
11. Light ON/ OFF Switch  
12. AC Recharge Adapter barrel connector receptacle  
ADDITIONAL FEATURES:  
• Heavy duty, professional quality  
• Easy-to-use: emergency jumpstarter for cars, light trucks, jet skis, snowmobiles, farm  
equipment, airplanes, boats, small SUVs and RVs, garden tractors, gasoline engine  
generators (almost any 12 Volt battery system)  
• Provides Instant 12 Volt DC Power - whenever, and wherever its needed  
Ideal for farm/ ranch, home, tailgate parties, beach, picnic, campsite, wilderness, utility power  
outages, emergency repair, etc  
Includes non-spillable, maintenance-free, heavy-duty, new high energy density 15 amp hour  
sealed battery  
• Sturdy and unique compact design provides up to 35 hours of completely portable 12 Volt  
DC power  
• Safe to use, transport, and store. Includes an audible polarity alarm  
Requires no maintenance (other than recharging) for optimum operation  
• Automatic taper charge for AC recharge  
• Audible alarm for reverse polarity  
• Molded high-impact case is tough and durable  
• Easy-to-read LED battery charging/ status indicators  
Built-in work/ emergency light with ultra-bright krypton bulb for roadside repairs and use in  
remote locations without utility power  
W ARN IN G:  
Never insert anything other than the supplied power/ recharging cords or recommended  
appliance power/ recharging cords into the charging or power receptacles on this unit.  
IMPO RTAN T:  
The safety ON/ OFF switch should be in the OFF position when the unit is charging or not  
in use.  
2.  
USING THE START-IT COMPACT PROAS A JUMPSTART SYSTEM  
W ARN IN GS:  
1. Before using this system to jump start any vehicle or boat, read and understand all  
instructions, safety tips, warnings and cautions, and first aid information provided in this  
manual and on the product labeling. Additional important information may also be  
provided by the vehicle ‘s battery system manufacturer.  
2. Be aware of first aid procedures before attempting jumpstart procedure.  
3. Always wear protective eyewear when working with a lead acid-type battery.  
4. Do not smoke or use inflammable items (matches, cigarette lighters, etc.) while working on a  
vehicles battery system.  
5. When using this jumpstarter in proximity to the vehicle ‘s battery and engine, stand the unit  
on a flat, stable surface, and be sure to keep all cords and cables well away from any  
moving parts.  
6. Check unit periodically for wear and tear. Replace worn or defective parts immediately -  
contact Vector Customer Service Department at (954) 584-4446 ext.19, toll-free: (954)  
584-5504 or through our internet address: www.vectormfg.com.  
5
7. Do not attempt to jumpstart a frozen battery.  
8. NEVER submerge this unit in water.  
9. Do not wear vinyl clothing when jumpstarting a vehicle-friction can cause dangerous static  
electricity sparks. Remove all jewelry or metal objects-they can cause short circuits or react  
with battery acid to cause severe burns. Remove or secure any loose clothing items, and  
restrain long hair, before attempting jumpstart procedure.  
WARN IN GS:  
Lead-acid batteries generate hydrogen gas during normal operation. More gas is generated  
when the battery is charging. Hydrogen gas is:  
• Explosive  
• Poisonous to Breathe  
• Highly Flammable  
RECOMMENDATIONS FOR OPTIMUM PERFORMANCE OF THE START-IT  
COMPACT PROJUMPSTART SYSTEM:  
CAUTIO N S:  
I. To avoid possible damage that may shorten the units working life, protect this unit from  
direct sunlight, direct heat and moisture.  
2. This system is to be used ONLY on vehicles, boats, garden tractors and gasoline powered  
generators with 12 Volt DC battery systems.  
3. This system is NOT designed to be installed as a replacement for a vehicular battery.  
4. Vehicles that have on-board computerized systems may be damaged if vehicle battery is  
jump-started. Before jumpstarting this type of vehicle, read the vehicles owners manual to  
confirm that external-starting assistance is advised.  
5. Excessive engine cranking can damage the vehicle ‘s starter motor. If the engine fails to start  
after the recommended number of attempts, discontinue jumpstart procedure and look for  
other problems that may need to be corrected.  
FIGURE 2 –SIDE VIEW  
CABLE CLAMP  
HOLSTERS  
COMPRESSOR  
ON/ OFF  
SWITCH  
CABLE CLAMP  
2.1  
EASY, STEP-BY-STEP JUMPSTARTING INSTRUCTIONS  
1. Turn OFF vehicle ignition and all accessories (radio, a/ c, lights, cell phone, etc.). Place  
vehicle in “park” and set the emergency brake.  
2. Make sure jumpstart systems Safety Switch is turned OFF.  
3. Remove booster clamps from protective holster (fig. 2): simply squeeze the handles and  
pull down on the clamp.  
Follow procedure for negative or positive grounded system, as follows:  
NEGATIVE GROUNDED SYSTEM:  
(NEGATIVE BATTERY TERMINAL IS CONNECTED TO CHASSIS-MOST COMMON METHOD:  
4. Connect positive (+) red clamp to vehicle battery ‘s positive terminal.  
5. Connect negative (-) black clamp to chassis or a solid, non-moving, metal vehicle component  
or body part. Never clamp directly to negative battery terminal or moving part. If the audible  
alarm sounds, the polarity is not correct. Reverse the connections.  
DO N O T TURN O N THE SAFETY SW ITCH W ITH ALARM SO UN DIN G.  
6
POSITIVE GROUND SYSTEMS:  
N O TE: In the rare event that the vehicle to be started has a Positive Grounded System (positive  
battery terminal is connected to chassis): Replace step 4 and 5 above with steps, 4a and  
4b and then proceed to steps 6 through 8 below.  
4a. Connect negative (-) black clamp to vehicle battery ‘s negative terminal.  
5a. Connect positive (+) red clamp to vehicle chassis or a solid, non-moving,  
metal vehicle component or body part. DO NOT clamp directly to positive  
battery terminal or moving part.  
6. Turn jumpstart system ‘s power switch to ON position.  
7. Start vehicle (do not turn key for longer than 5-6 seconds).  
8. After vehicle starts, turn jumpstart system ‘s Safety Switch to OFF position. Remove clamps  
(disconnect the negative (Black) jumper cable first; followed by the positive (Red) jumper  
cable) and replace them in the built-in storage holsters. Squeeze the handles and slide the  
clamp into position and release your grip.  
CAUTIO N S:  
1.If engine fails to start, leave ignition key turned off, make sure safety switch is off and  
disconnect the negative (-) clamp first, then the positive (+) clamp. Try again later - the engine  
may be flooded.  
2. Recharge jumpstart system after each use.  
W ARN IN GS:  
• Always disconnect the engine jumper clamp first; followed by the battery jumper clamps  
• Never allow red and black clamps to touch each other or another common metal conductor  
– this could cause damage to the unit and/ or create sparking/ explosion hazard  
There is a risk of explosive gases being released when batteries are improperly charged or  
discharged, failure to follow instructions may cause property damage, explosive hazard,  
and/ or personal injury  
• Always use protective eyewear when using this product: contact with battery acid may cause  
blindness and/ or severe burns  
Keep out of reach of children  
• ALWAYS store battery clamps in built-in holsters when not in use and never touch battery  
clamps together-this can cause dangerous sparks, power arcing and/ or explosion  
FIRST AID:  
Sk in : If battery acid comes in contact with skin, rinse immediately with water, then wash  
thoroughly with soap and water–If redness, pain, or irritation occurs, seek immediate  
medical attention.  
Ey e s: If battery acid comes in contact with eyes, flush eyes immediately for minimum of 15  
minutes - SEEK IMMEDIATE MEDICAL ATTENTION.  
3.  
CHARGING/ RECHARGING  
For maximum battery life, we recommend that the START-IT COMPACT PROsystem be kept  
fully charged at all times. If the battery is allowed to remain in a discharged state, battery life  
will be shortened. N O TE: Recharging battery after each use will prolong battery life; frequent  
discharges between recharges will reduce battery life.  
7
3.1  
110/ 120-VOLT AC CHARGING  
IMPO RTAN T:  
• MAKE SURE ALL SWITCHES ARE TURNED OFF DURING RECHARGING  
• Charge unit for full 24 hours, prior to first use  
Recharge unit fully after each use  
Recharge unit every two months, when it has not been used  
CAUTIO N : Make sure compressor switch is off otherwise the battery will not accept the  
charge.  
1. Simply plug the 110/ 120 volt AC plug of the AC/ DC adapter/ charger cord into any  
standard 110/ 120 volt AC wall outlet.  
2. Plug the barrel connector attached to the AC/ DC adapter cord into the small barrel  
receptacle on the jumpstarter.  
3. Charge this device for at least 14-16 hours or until the FULL indicator lights.  
4. When charging is completed and the FULL light lights, remove the power cord and store in a  
safe place.  
N O TE: The unit cannot be overcharged using the AC method.  
3.2  
12 VOLT DC CHARGING  
The START-IT COMPACT PROsystem also comes with a DC/ DC charging cord, for  
recharging the unit from a 12 volt DC cigarette lighter socket in a vehicle or boat.  
N O TE: This recharging method will NOT recharge the unit as effectively as recharging from a  
110/ 120 volt AC outlet. The 12 Volt DC recharging procedure is recommended only  
when it is necessary, as continued use of the 12 Volt DC recharging procedure may shorten  
the battery systems life.  
W ARN IN G:  
Do not recharge for more than 3-4 hours maximum using 12 Volt DC method.  
N O TE: If unit is fully discharged, it is recommended that the vehicle being used for recharging  
be left running while the unit is being charged via the 12 Volt DC method.  
1. Insert one end of the DC/ DC charging cord into the 12 Volt DC cigarette lighter receptacle  
on the vehicle or boat.  
2. Insert the plug at the other end of this power cord into the 12 Volt DC receptacle on the front  
panel of the unit.  
3. Charge the unit until the green FULL indicator lights when Charge Status Indicator Button is  
pressed. DO NOT EXCEED 3-4 HOURS MAXIMUM.  
4. When charging is completed, remove the power cord and store in a safe place.  
3.3  
ESTIMATED BATTERY LIFE  
Table I shows the relationship of the frequency of use between recharging and the expected  
number of discharge/ recharge cycles.  
Table I - Estimated Battery Life  
BETWEEN RECHARGES (LIFETIME OF UNIT BATTERY)  
USE  
RECHARGES  
................................................................ 1000+  
................................................................ 700+  
1
5
10 ............................................................... 500+  
8
4.  
OPERATION AS A 12 VOLT PORTABLE POWER SUPPLY  
N O TE: Make sure that the unit ‘s Safety ON/ OFF switch is ALWAYS in the OFF position when  
using the 12 Volt DC accessory outlet.  
1. Lift up the cover of the unit‘s 12 Volt DC cigarette lighter-type accessory receptacle (See Figure 1).  
2. Insert the 12 volt DC plug from the appliance into the receptacle on the unit.  
3. Switch on the appliance, and operate as usual.  
CAUTIO N : Do not use this unit to operate appliances that draw more than 20 amps.  
Estimated 12 volt DC usage times  
Table II shows the estimated 12 volt DC operation times when using a fully-charged system.  
Table II - START-IT COMPACT PRO™ as a 12 Volt DC Power Supply  
APPLIANCE TYPE ESTIMATED POWER ESTIMATED USAGE CONSUMPTION (IN WATTS) TIME (IN HOURS)  
CELL PHONE................................................... 1 .................................. 120 hrs. Talk Time  
FLUORESCENT LIGHT ...................................... 4 .............................................. 30  
RADIO, FAN, DEPTH FINDER........................... 9 .............................................. 14  
CAMCORDER, VCR, SPOTLIGHT..................... 15 .............................................. 8  
POWER TOOLS, BILGE PUMP ......................... 24 .............................................. 5  
ELECTRIC COOLER ......................................... 48 .............................................. 3  
CAR VACUUM ............................................... 80 ............................................ 1.0  
N O TE: ALL TIMES ARE APPROXIMATE AND BASED UPON A FULLY CHARGED UNIT.  
5.  
EMERGENCY/ WORK LIGHT  
The Work light is controlled by its On/ Off switch. Make sure the lamp is turned OFF when the  
unit is being recharged or stored.  
6.  
AIR COMPRESSOR/ TIRE INFLATOR  
The built-in 12 Volt DC air compressor is the ultimate compressor for all Vehicles, trailer tires  
and recreational inflatables. Three different sized nozzles are supplied. Each nozzle will clip on  
the end of the standard tire valve connector located at the free end of the compressor hose. The  
compressor nozzles are stored inside the Cable Hatch. The compressor hose with tire fitting is  
stored in a retaining channel between the jumper cable channels on the rear of the unit. The  
compressors ON/ OFF Switch is located on the side of the Main Unit near the AC Recharge  
Port. The compressor can operate long enough to fill up to 3 average sized tires before the  
battery must be recharged. See figure 3 for Hose and Nozzle storage.  
FIGURE 3 BACK VIEW  
COMPRESSOR  
HOSE  
LIGHTED  
GAUGE  
NOZZLES  
TIRE VALVE  
NOZZLE  
STORAGE  
9
6.1  
COMPRESSOR USE  
IMPO RTAN T: Read Instructions Carefully To Avoid Possible Injury Or Property Damage.  
The compressor may be used by removing the air hose from its storage channel and if  
required, fitting an appropriate nozzle to the air hose. An On/ Off switch located on the side  
of the unit controls the power to the compressor and the gauge light. Refer to Figures 2 and 3  
for locations of compressor hose, nozzle storage hatch and hose. Return hose to its storage  
compartment after use.  
6.2  
WARNINGS FOR COMPRESSOR USE  
The compressor is capable of inflating up to 260 pounds per square inch (PSI) pressure. To  
avoid over-inflation, carefully follow instructions on articles to be inflated. Never exceed  
recommended pressures. Bursting articles can cause serious injury. Always check pressure with  
the pressure gauge. Never leave compressor unattended while in use. Allow unit to cool after  
10 minutes of continuous operation.  
6.3  
TIRE INFLATION OR PRODUCTS WITH A VALVE STEM  
1. Place connector (chuck) on valve stem.  
2. Push connector toward valve stem and close thumb latch.  
3. Make sure connector is pushed on to valve stem as far as possible before closing thumb latch.  
4. Check pressure with the pressure gauge (Refer to paragraph 6.5).  
5. When desired pressure is reached, open thumb latch and remove connector from valve stem.  
6. Turn OFF Compressor Power Switch.  
7. Store compressor hose and tire fitting in storage compartment.  
IMPO RTAN T: Always leave the thumb latch in the open position when storing unit.  
6.4  
INFLATE OTHER ARTICLES (WITHOUT VALVE STEM)  
Inflation of other items requires use of one of the adapters (nozzles).  
1. Open the hatch and remove the nozzles noting their storage positions.  
2. Insert appropriate adaptor (e,g. needle) into connector (chuck) and close thumb latch.  
3. Refer to “Typical Inflation Times” for approximate pressure and time. Small items such as  
volleyballs, footballs, etc. inflate very rapidly.  
4. Insert adaptor (e.g needle) into item to inflate to appropriate pressure.  
6. Turn ON compressor switch - inflate to desired pressure or fullness (refer to paragraph 5.5).  
7. Remove adaptor.  
6.5  
TYPICAL INFLATION TIMES  
The following are approximate pressure and inflation times for various items.  
W ARN IN G:  
Always follow tire manufacturers recommendations for pressure on item to be inflated.  
VEHICLE AND TRAILER TIRES  
TIRE SIZE  
PRESSURE  
TIME FROM “0” PRESSURE  
155/ 80R 13" .......................................... 26 psi ................................................ 2.50 min.  
185/ 70R 14" .......................................... 30 psi ................................................ 4.50 min.  
235/ 75R 15" .......................................... 30 psi ................................................ 6.50 min.  
235/ 85R 16" .......................................... 50 psi .............................................. 16.00 min.  
BICYCLE TIRES  
TIRE SIZE  
PRESSURE  
TIME FROM “0” PRESSURE  
27 x 1" racing ......................................... 10 psi .................................................. 40 sec.  
INFLATABLE ARTICLES  
TIRE SIZE  
PRESSURE  
TIME FROM “0” PRESSURE  
Football ................................................... 13 PSI .............................................. 24 seconds  
Basketball ................................................. 9 PSI ............................................... 20 seconds  
Volleyball ................................................. 5 PSI................................................. 6 seconds  
10  
7.  
REPLACEMENT PARTS  
For replacement parts (bulbs, batteries, fuses, etc.), contact Vector Customer Service:  
(954) 584-4446 or toll-free (866) 584-5504.  
7.1  
BULB REPLACEMENT  
Tools needed - small Phillips screwdriver.  
1. Unscrew (counterclockwise) and remove two Phillips screws.  
2. Remove the lens cover.  
3. Remove the burned-out bulb.  
4. Replace with a new bulb (12-volt 0.2 amp Krypton bulb).  
5. Snap the lens cover back into place.  
6. Replace (clockwise) the screws and carefully tighten. Do not over tighten!  
7.2  
BATTERY REPLACEMENT  
It is recommended that the unit be returned to Vector Customer Service for battery replacement:  
Contact (954) 584-4446 or toll-free (866) 584-5504 ext.19.  
W ARN IN GS:  
• Do not dispose of the battery in fire as this may result in an explosion  
Before disposing of the battery, protect exposed terminals with heavy-duty electrical tape to  
prevent shorting (shorting can result in injury or fire)  
• Do not expose battery to fire or intense heat as it may explode  
7.3  
BATTERY DISPOSAL:  
This unit contains a maintenance-free, non-spillable, sealed lead-acid battery–this battery is fully  
recyclable and should be accepted at any location that accepts common automotive starter batteries.  
Examples of places that accept these batteries are: County or municipal recycling drop-off centers,  
scrap metal dealers and retailers who sell automotive replacement lead acid starter batteries. For  
more information on recycling this battery, call toll-free 877/ 288-7722.  
8.  
SPECIFICATIONS  
Model ..................................................................................... VEC020C Voltage 12 VDC  
Boost Power ................................................................ 350 Instantaneous Cranking Amps  
Peak Ampere Power ........................................................................................ 900 Amps  
Battery Type .......................... Sealed, high energy density, AGM, lead-acid, rechargeable,  
............................................................. maintenance-free, 12 volt DC, 15 Amp-hour  
Bulb ......................................................................................... 12 Volt 0.2 Amp Krypton  
Booster Cables ................................. #6AWG welding cable with 350 Amp copper clamps  
Accessory Socket.............................................................. Self-Resetting Breaker 20 Amps  
Charging Cord ................................................................................................ 12 Volt DC  
Adapter/ Charger ...................................... 110/ 120 Volt AC(500mA, 12 Volt DC Output)  
Reverse Polarity Detection .......................................................................... 1.5 Volts (min)  
HEIGHT ................................................................................................ 8.5 in. (21.6 cm)  
DEPTH ..................................................................................................... 8.25 in (21 cm)  
WIDTH .................................................................................................... 9.8 in(24.9 cm)  
WEIGHT ............................................................................................. 12.5 Lbs (5.67 Kg)  
1 1  
VECTOR 120 DAY/ TWO YEAR LIMITED WARRANTY PROGRAM  
This limited warranty program is the only one that applies to this product, and it sets forth all the  
responsibilities of Vector Manufacturing, Ltd., regarding this product. There is no other warranty, other  
than those described herein.  
This Vector Manufacturing, Ltd. product is warranted, to the original purchaser only, to be free of defects in  
materials and workmanship for 120 days from the date of purchase without additional charge. This  
warranty may be extended to two years from date of purchase by paying an Extended Warranty fee (see  
below). The warranty does not extend to subsequent purchasers or users. Vector Manufacturing, Ltd. will  
not be responsible for any amount of damage in excess of the retail purchase price of the product under  
any circumstances. Incidental and consequential damages are specifically excluded from coverage under  
this warranty.  
This product is not intended for commercial use. This warranty does not apply to accessories or damage to  
units from misuse or incorrect installation. Misuse includes wiring or connecting to improper polarity  
power sources.  
RETURN/ REPAIR POLICY: Defective products, other than accessories, may be returned postage prepaid to  
Vector Manufacturing. Any defective product, other than accessories, that is returned to Vector Manufac-  
turing within 30 days of the date of purchase will be replaced free of charge. If such a product is returned  
more than 30 days but less than 120 days from the purchase date, Vector Manufacturing will repair the  
unit or, at its option, replace it free of charge. If The Extended Warranty was activated, this repair or  
replacement period extends to two years from the purchase date.  
If the unit is repaired, new or reconditioned replacement parts may be used, at Vector Manufacturings  
option. A unit may be replaced with a new or reconditioned unit of the same or comparable design. The  
repaired or replaced unit will then be warranted under the terms of the remainder of the warranty period.  
The customer is responsible for the shipping charges on all returned items. During the warranty period,  
Vector Manufacturing, Ltd. will be responsible for the return shipping charges.  
LIMITATIONS: This warranty does not cover accessories, bulbs, fuses and batteries, defects resulting from  
normal wear and tear (including chips, scratches, abrasions, discoloration or fading due to usage or  
exposure to sunlight), accidents, damage during shipping to our service facility, alterations, unauthorized  
use or repair, neglect, misuse, abuse, failure to follow instructions for care and maintenance, fire, flood,  
and Acts of God.  
If your problem is not covered by this wa rra nty, ca ll our Technica l Support Depa rtment a t  
(954) 584-4446 or toll free at 866-584-5505 for general repair information and charges if applicable.  
You may also contact us through our website at www.vectormfg.com.  
STATE LAW RIGHTS: This warranty gives you specific legal rights. Some states do not allow limitations on  
how long an implied warranty lasts or the exclusion or limitation of incidental or consequential damages,  
so the exclusions or limitations stated herein may not apply. This warranty gives the purchaser specific  
legal rights; other rights, which vary from state to state, may apply.  
TO REQ UEST WARRANTY SERVICE FO R THIS PRO DUCT: Conta ct Vector Ma nufa cturing  
Technical Support by telephone, fax or mail. We suggest that you keep the original packaging in case you  
need to ship the unit. When returning a product, include your name, address, phone number, dated sales  
receipt (or copy), and a description of the reason for return and product serial number. After repairing or  
replacing the unit, we will make every effort to return it to you within four weeks.  
WARRANTY ACTIVATIO N: Plea se complete Wa rra nty Activa tion Ca rd a nd ma il to Vector  
Manufacturing. If activating Extended Two Year Warranty, (total two years) enclose check or money order  
for $25.00 Enter “VEC020C” as Model and CompactPro/ Compressor as Product Type”.  
All Vector Manufacturing, Ltd. products must be registered within (30) days of purchase to activate this  
warranty. Mail the completed registration form, along with a copy of the original sales receipt to:  
ATTN.: CUSTOMER SERVICE / VECTOR MANUFACTURING, Ltd.  
4140 SW 28th Way, Ft. Lauderdale, FL 33312  
PH: 954-584-4446 • TOLL FREE: 866-584-5504 • Fax: 954-584-5556.  
You may also contact us at our web site www.vectormfg.com.  
WARRANTY MUST BE PURCHASED W ITHIN 3 0 DAYS O F PRO DUCT PURCHASE DATE.  
WARRANTY IS NON-TRANSFERABLE AND NON-REFUNDABLE.  
© 2001 VECTOR MANUFACTURING, Ltd. • FT. LAUDERDALE, FL 33312 MADE IN CHINA  

Lexmark X 954dhe User Manual
Mitsubishi Electronics Lossnay Lgh 15rx4 E User Manual
Panasonic Cu A24ctp5 User Manual
Samsung Avmwc032ca0 User Manual
Sharp Afs80fx User Manual
Sharp Fp N60cx User Manual
Sharp Mx 2310u User Manual
Soleus Air Ph5 S Series User Manual
Toshiba Ras 10javp E User Manual
Vornado Air Cleaner Whole Room Air Purifier User Manual